Integrating 9load into the LinuxBIOS
D1114662405
Auriel (82.182.149.46)
#To make this sane we will show latest developments first.
#
#5/5/2003 What we're going to put in here now is the update of how
#the system works now. The base test hardware is the PCM-5923 from
#Advantech. We built a standard LinuxBIOS for this board that uses
#Etherboot to load the 9load image from Compact Flash. I can send you
#the flash ROMIMAGE on request so that rather than fool around with
#LinuxBIOS you can just use our image.
#
#We've had to make fixes to 9load and we are now trying to back those
#changes out as much as possible to minimize 9load variance.
#
#The parts you need to replicate our setup:
#
# * [Advantech PCM-5823 |
# http://www.advantech.com/products/Model_Detail.asp?model_id=1-D6M06&bu=Advantech PCM-5823]
# * Any kind of Compact Flash > 1 MB in size
# * Replacement flash part (SST 28SF040 is what we use)
# * If you are building LinuxBIOS, a Linux box. If you are not, a way
# to reprogram the FLASH and a copy of our flash image.
#
#If you just the flash image from us, we can also send the working
#9load image (which you burn onto the CF) and a working Plan 9 kernel
#image which you tftp download. This kernel knows how to use CMOS for
#its nvram.
#
#Base document follows:
#
#LinuxBIOS can load lots of different "payloads", i.e. ELF images in
#FLASH. In this document we will go over how we got 9load into FLASH,
#and thus made nodes that can boot as dedicated Plan 9 CPU nodes.
#
#NOTE: also check (http://www.acl.lanl.gov/plan9/flash/(broken
#link!)) for additional information!
#
#This documentation pertains to the setup, configuration and means of
#getting Plan 9 booted with LinuxBIOS. It consists of the following
#parts:
#
# * 0. Preamble
# * 1. Development setup -- getting started. file organization in
# Plan9 and Linux
# * 2. Source code explanation -- diffs with 4th edition p9 source
# with explanation
# * 3. Source code -- tarred & gzipped
#
#------------------------------------------------------
#PREAMBLE:
#
#This document discusses changes made to the source of Plan9 to get
#it going on at least one machine booted by LinuxBIOS. The goal of
#the project was to have a standalone Plan9 cpu server that neither
#had nor required moving parts. Most of this was accomplished with
#the help of Ron Minnich, without whose support and in-depth
#knowledge of computer hardware minions would still be scratching
#their head trying to find out why nothing happens after the kernel
#is downloaded...
#
#------------------------------------------------------
#1. DEVELOPMENT SETUP:
#
#For a succesfull modification to the source one needs to have access
#to the following:
#
# * 1.1 Plan9 network (including file servers, cpu servers and
# terminals ([http://pages.cpsc.ucalgary.ca/~mirtchov/lanlp9/])
# * 1.1.1 It is possible to work from a standalone P9 terminal,
# though this setup would be trickier
# * 1.2 Plan9 source (usually comes with access to the P9 network
# and/or a P9 installation)
# * 1.3 A Linux machine (used to compile the LinuxBIOS part)
# * 1.4 Some hardware that LinuxBIOS works with
# * 1.(5-9) Lots of patience
#
#Plan9 setup:
#
#The setup for P9 uses the fact that the operating system supports
#union directories. What that gives us is the ability to store only
#those files we modify in our local directory, and bind them when
#necessary on top of the standard kernel tree (in /sys/src/)... In
#fact this results in a carefully crafted namespace that could be
#used in a single terminal window (or, if so willing in an entire rio
#session on a cpu server) to present a decent development
#environment, while the rest of the screen, session or terminals keep
#the common, non-development view of the system. Ultimately this
#allows for several different developments to go on at the same time,
#(example will be shown in a bit) -- compiling kernels in one window,
#9load bootloaders in another window, while being able to see the
#normal, unmodified kernel tree in a third window for comparison. All
#in the same directory.
#
#How it actually works:
#
#In brief, LinuxBIOS starts up on the hardware, find and loads
#Plan9's bootloader (9load masked as an elf32 image so it can be
#recognized by LinuxBIOS), 9load then prompts for kernel or attempts
#to etherboot one, downloads it, uncompresses it and jumps to it.
#Voila.
#
#Details follow:
#
#You compile (make) a 9load image tailored to work with
#
#LinuxBIOS:
#
#! p9% lbbind # bind the development tree...
#! p9% mk 9loadlb # in the mkfile there's a special
#! 8a -DLinuxBios -o ll.8 l.s # configuration for linuxbios
#! 8c -FVw -I. alarm.c # kernels carrying the necessary
#! 8c -FVw -I. cga.c # #define's and linking 9load
#! 8c -FVw -I. clock.c # at 0x800000
#! 8c -FVw -I. console.c
#! 8c -FVw -I. dosboot.c
#! 8c -FVw -I. donprint.c
#! 8c -FVw -I. devfloppy.c
#! 8c -FVw -I. dma.c
#! 8c -FVw -I. ilock.c
#! 8c -FVw -I. kbd.c
#! 8c -FVw -I. queue.c
#! 8c -FVw -I. trap.c
#! 8c -FVw -I. 8250.c
#! warning: 8250.c:130 param declared and not used: arg
#! 8c -FVw -I. apm.c
#! 8c -FVw -I. boot.c
#! 8c -FVw -I. devpccard.c
#! 8c -FVw -I. conf.c
#! 8c -FVw -I. devi82365.c
#! 8c -FVw -I. devsd.c
#! 8c -FVw -I. inflate.c
#! 8c -FVw -I. load.c
#! warning: load.c:159 no return at end of function: myboot
#! load.c:280 function args not checked: pcihinv
#!
#! 8c -FVw -I. memory.c
#! 8c -FVw -I. part.c
#! 8c -FVw -I. pci.c
#! 8c -FVw -I. sdata.c
#! 8c -FVw -I. sdmylex.c
#! 8c -FVw -I. sd53c8xx.c
#! 8c -FVw -I. sdscsi.c
#! 8c -FVw -I. bootp.c
#! 8c -FVw -I. ether.c
#! 8c -FVw -I. ether2114x.c
#! 8c -FVw -I. ether2000.c
#! 8c -FVw -I. ether589.c
#! 8c -FVw -I. ether79c970.c
#! 8c -FVw -I. ether8003.c
#! 8c -FVw -I. ether8139.c
#! 8c -FVw -I. ether82557.c
#! 8c -FVw -I. ether83815.c
#! 8c -FVw -I. ether8390.c
#! 8c -FVw -I. etherec2t.c
#! 8c -FVw -I. etherelnk3.c
#!
#! 8l -o 9loadlb -H3 -T0x80800000 -l ll.8 alarm.8 cga.8 clock.8
#! console.8 dosboot.8 donprint.8 devfloppy.8 dma.8 ilock.8 kbd.8
#! queue.8 trap.8 8250.8 apm.8 boot.8 devpccard.8 conf.8 devi82365.8
#! devsd.8 inflate.8 load.8 memory.8 part.8 pci.8 sdata.8 sdmylex.8
#! sd53c8xx.8 sdscsi.8 bootp.8 ether.8 ether2114x.8 ether2000.8
#! ether589.8 ether79c970.8 ether8003.8 ether8139.8 ether82557.8
#! ether83815.8 ether8390.8 etherec2t.8 etherelnk3.8 -lflate -lc
#!
#! ls -l 9loadlb
#!
#! --rwxr-xr-x M 9 andrey andrey 178320 Jun 20 11:34 9loadlb
#!
#! p9%
#!
#! 9loadlb is a special configuration in the mkfile that will
#!
#! #define 'LinuxBios' during the compilation and will link 9loadlb at
#! 0x800000 (that's where LinuxBIOS will jump to).
#!
#! Next step is to copy 9loadlb to the linux machine (usually you would
#! scp it a level below the mkelf/ directory in snaresland):
#!
#! fbsd$ scp plan9:src/boot/pc/9loadlb ../9load.800000
#!
#! [email protected]'s password:
#!
#! 9loadlb 100% |*****************************| 174 KB 00:00
#!
#! fbsd$
#
#Then run the 'mymk' script in mkelf:
#
#! snares$ pwd
#! /users/andrey/kern/mkelf
#! snares$ ./mymk
#! #!/bin/sh -v
#! cd 9load
#! cp ~/kern/9load.800000 .
#! make all4
#! ./mkas < 9load.800000 > 9l.s
#! as -o 9l.o 9l.s
#! ld -T elfImage.lds.800000 -o 9l.elf 9l.o
#! ld: warning: cannot find entry symbol startup_32; defaulting to
#! 00800000
#! cp 9l.elf ..
#! cd ..
#!
#! bin/mkelfImage --kernel=9l.elf
#!
#! Running gcc -O2 -DDEFAULT_ROOT_DEV='(((0x3<<8)| 0))'
#! -DDEFAULT_COMMAND_LINE='""' -DDEFAULT_PROGRAM_VERSION='""' -c
#! /users/andrey/kern/mkelf/share/mkelfImage/elf32-i386/convert_params.c -o /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/convert_params_6384.o
#!
#! Running gcc -O2 -DDEFAULT_ROOT_DEV='(((0x3<<8)| 0))'
#! -DDEFAULT_COMMAND_LINE='""' -DDEFAULT_PROGRAM_VERSION='""' -c
#! /users/andrey/kern/mkelf/share/mkelfImage/elf32-i386/head.S -o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/head_6384.o
#!
#! Running ld -o elfImage.fat -T
#! /users/andrey/kern/mkelf/share/mkelfImage/elf32-i386/elfImage.lds
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/kernel_piggy_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/ramdisk_piggy_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/convert_params_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/head_6384.o Running
#! ld -o elfImage.fat -T
#! /users/andrey/kern/mkelf/share/mkelfImage/elf32-i386/elfImage.lds
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/kernel_piggy_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/ramdisk_piggy_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/convert_params_6384.o
#! /am/mother-v2-e5/vol/vol0/u0/andrey/kern/mkelf/head_6384.oBFD:
#! elfImage.fat: warning: Empty loadable segment detected
#!
#! checksum: dc7c
#!
#! echo done
#!
#! done
#
#The script is a bit ugly, but we strive not for beauty... You'll
#find it below, or in the linux bundle... Next step is to scp back
#the 9load (masked as an elfImage) to a place where it could be
#burned in flash, or if you want to debug, downloaded by an etherboot
#LinuxBIOS:
#
#! fbsd$ scp elfImage plan9:/386/9pcblah
#! [email protected]'s password:
#! elfImage 100% |*****************************| 190 KB 00:00
#! scp: can't wstat /386/9pcblah: wstat -- attempt to change qid.vers
#! fbsd$
#
#Ignore the error message if you see it... In this case, the dhcp
#server has been instructed to provide /386/9pcblah as the kernel to
#a bootp request from the machine we work with (based on that
#machine's ethernet address, ask dpx@acl for more details).
#
#NOTE: if you think that the 9load will work fine, just tell Ron to
#burn it in flash for you.. In this case you need to put the 9pccpu
#kernel in /386/9pcblah instead :)
#
#File organization:
#
#create a $home/src directory to store all the modified files in. the
#then in $home/src recreate all the directories present in /sys/src,
#which pertain in your current development. in my case it was
#/sys/src/9, /sys/src/boot, /sys/src/libauthconfig, and then
#recursively recreate all other directories present there. here's a
#real-life example:
#
#! p9% du /usr/andrey/src | awk '{print $2}'
#! /usr/andrey/src/9/pc
#! /usr/andrey/src/9/ip
#! /usr/andrey/src/9/alphapc
#! /usr/andrey/src/9/bitsy
#! /usr/andrey/src/9/boot
#! /usr/andrey/src/9/port
#! /usr/andrey/src/9/mtx
#! /usr/andrey/src/9
#! /usr/andrey/src/libauthsrv
#! /usr/andrey/src/boot/alphapc
#! /usr/andrey/src/boot/arm
#! /usr/andrey/src/boot/pc
#! /usr/andrey/src/boot
#! /usr/andrey/src/cmd/aux/vga
#! /usr/andrey/src/cmd/aux
#! /usr/andrey/src/cmd/auth/factotum
#! /usr/andrey/src/cmd/auth/lib
#! /usr/andrey/src/cmd/auth/secstore
#! /usr/andrey/src/cmd/auth
#! /usr/andrey/src/cmd
#! /usr/andrey/src
#! p9%
#
#Then if you want to edit /sys/src/9/pc/pci.c just do:
#
#! cp /sys/src/9/pc/pci.c $home/src/9/pc/pci.c
#
#Scripts:
#
#Several scripts are used to automate the binding process and to make
#your life easier. Remember that after the boot-up the machine is in
#a non-development state, i.e. it does not know that you have made
#any modification to the kernel source -- you have to tell it to
#change the namespace accordingly, so that when you type 'mk' in
#/sys/src/9/pc it will compile your own files instead of somebody
#else's... The scripts will do the modification to the namespace for
#you, just execute them before you start working on the code (think
#of it as a 'start your engines' of some sort). Here are the scripts
#(they differ because one does binding of the $home/src/9 as the
#kernel tree -- something I use for writing drivers to support
#several graphics cards, i.e. non-LinuxBIOS kernels) and the other
#binds $home/src/linuxbios/ which is the same as $home/src/9, but the
#files therein are LinuxBIOS-related. Copy those files in
#$home/bin/rc and chmod 755 them:
#
#! p9% cat /usr/andrey/bin/rc/kbind
#! #!/bin/rc
#! # this does bindings for the non-linuxbios kernel sources
#! # and the 9load linuxbios sources
#!
#! # 9
#! bind -cb $home/src/9/pc /sys/src/9/pc
#! bind -cb $home/src/9/ip /sys/src/9/ip
#! bind -cb $home/src/9/alphapc /sys/src/9/alphapc
#! bind -cb $home/src/9/bitsy /sys/src/9/bitsy
#! bind -cb $home/src/9/boot /sys/src/9/boot
#! bind -cb $home/src/9/port /sys/src/9/port
#! bind -cb $home/src/9/mtx /sys/src/9/mtx
#!
#! #boot
#! bind -cb $home/src/boot/alphapc /sys/src/boot/alphapc
#! bind -cb $home/src/boot/arm /sys/src/boot/arm
#! bind -cb $home/src/boot/pc /sys/src/boot/pc
#!
#! #fs
#! bind -cb $home/src/fs/port /sys/src/fs/port
#! bind -cb $home/src/fs/choline /sys/src/fs/choline
#! bind -cb $home/src/fs/dev /sys/src/fs/dev
#! bind -cb $home/src/fs/emelie /sys/src/fs/emelie
#! bind -cb $home/src/fs/ip /sys/src/fs/ip
#! bind -cb $home/src/fs/pc /sys/src/fs/pc
#! bind -cb $home/src/fs/roro /sys/src/fs/roro
#! bind -cb $home/src/fs/sony /sys/src/fs/sony
#!
#! #cmd
#!
#! bind -cb $home/src/cmd /sys/src/cmd
#!
#! p9%
#
#The #cmd part is not really necessary, but i keep in there
#
#stuff i do with P9 commands...
#
#! p9% cat /usr/andrey/bin/rc/lbbind
#! #!/bin/rc
#! # linuxbios stuff
#!
#! # 9
#! bind -cb $home/src/linuxbios/pc /sys/src/9/pc
#! bind -cb $home/src/linuxbios/ip /sys/src/9/ip
#! bind -cb $home/src/linuxbios/alphapc /sys/src/9/alphapc
#! bind -cb $home/src/linuxbios/bitsy /sys/src/9/bitsy
#! bind -cb $home/src/linuxbios/boot /sys/src/9/boot
#! bind -cb $home/src/linuxbios/port /sys/src/9/port
#! bind -cb $home/src/linuxbios/mtx /sys/src/9/mtx
#!
#! #boot
#! bind -cb $home/src/boot/alphapc /sys/src/boot/alphapc
#! bind -cb $home/src/boot/arm /sys/src/boot/arm
#! bind -cb $home/src/boot/pc /sys/src/boot/pc
#!
#! #fs
#! bind -cb $home/src/fs/port /sys/src/fs/port
#! bind -cb $home/src/fs/choline /sys/src/fs/choline
#! bind -cb $home/src/fs/dev /sys/src/fs/dev
#! bind -cb $home/src/fs/emelie /sys/src/fs/emelie
#! bind -cb $home/src/fs/ip /sys/src/fs/ip
#! bind -cb $home/src/fs/pc /sys/src/fs/pc
#! bind -cb $home/src/fs/roro /sys/src/fs/roro
#! bind -cb $home/src/fs/sony /sys/src/fs/sony
#!
#! #cmd
#! bind -cb $home/src/cmd /sys/src/cmd
#!
#! p9%
#
#Actually, only the lbbind command is needed -- that'll bind
#
#all sources from the source tree
#
#An example of a typical P9 session follows:
#
#! p9% lbbind
#!
#! p9% cd /sys/src/9/pc
#!
#! # edit some files, make some changes, etc...
#!
#! #make a cpu kernel
#!
#! p9% mk 'CONF=pccpu'
#!
#! 8c -FVw ether79c970.c
#!
#! 8c -FVw vgabt485.c
#!
#! # lots of files being compiled, here's where your errors will happen
#! #
#! # now you have a decent kernel, copy it somewhere where it could be etherbooted
#!
#! p9% cp 9pccpu
#!
#! # clean up -- not really necessary, but sometimes fun :)
#!
#! p9% mk clean
#!
#! rm -f *.[v4586xq7] *.root.s cfs.h fs.h init.h conf.h *.out
#!
#! for(i in pc pccpu pcdisk)
#!
#! mk $i.clean
#!
#! rm -f pc.c [9bz]pc [9bz]pc.gz bootpc.*
#!
#! rm -f pccpu.c [9bz]pccpu [9bz]pccpu.gz bootpccpu.*
#!
#! rm -f pcdisk.c [9bz]pcdisk [9bz]pcdisk.gz bootpcdisk.*
#!
#! p9%
#!
#! # to stop a development session just delete the terminal window,
#! # your files will be saved there :)
#
#------------------------------------------------------
#Linux:
#
#Here you'll need ron's help! CVS update the latest from the freebios
#distribution, then guntar the mkelf.tgz file included, then get Ron
#to make LinuxBIOS proper so you can combine it with 9loadlb... I
#pretty much know nothing about this process. As far as I am
#concerned I may as well be sitting around waving a chicket at the
#screen while Ron does everything... After the setup, just use the
#'mymk' script as above and enjoy :)
#
#------------------------------------------------------
#2. SOURCE CODE DIFFS WITH EXPLANATIONS:
#
#/sys/src/boot/pc/mkfile -- the file was changed to accomodate my
#Plan9 endeavours. a new target was added, namely the 9loadlb
#linuxbios-enabled kernel. the difference is that the linuxbios code
#is #ifdef-ed LinuxBios:
#
#! p9% diff boot/pc/mkfile /sys/src/boot/pc/mkfile
#! 7d6
#! < 9loadlb\
#! 95,98d93
#! < 9loadlb: ll.$O $CORE $LOAD $ETHER
#! < $LD -o $target -H3 -T0x80800000 -l $prereq -lflate -lc
#! < ls -l $target
#! <
#! 118,120d112
#! <
#! < ll.$O: l.s
#! < $AS -DLinuxBios -o ll.$O l.s
#! p9%
#
#/sys/src/boot/pc/l.s -- the real mode code is commented out (rather,
#ifdef'd), 9load is entered in protected mode. code is added to load
#the GDT. some attempts to fix the IRQ routing problem but nothing is
#tested extensively. we ended up chasing a bug for a long time with:
#
#! MOV AX, SS
#
#and ended up fixing it somewhat miraculously. it never appears in
#normal bios boots...
#
#stuff like:
#
#! MOVL $0x80, DX
#! MOVB $0x19, AL
#! OUTB
#
#is simply outputting to the post card (ask Ron for details on
#Post-Card debugging! It's the most fun you can have without having
#to go outside and exercise!
#
#diff:
#
#! p9% diff boot/pc/l.s /sys/src/boot/pc/l.s
#! 20,24d19
#! <
#! < MOVL $0x80, DX
#! < MOVB $0x11, AL
#! < OUTB
#! <
#! 27c22
#! < #ifndef LinuxBios
#! ---
#! >
#! 200,202d194
#! <
#! <
#! <
#! 209c201
#! < MOVL $1,AX
#! ---
#! > LWI(1, rAX)
#! 213,216d204
#! < /* MOVL CR0,AX
#! < ORL $1,AX
#! < MOVL AX,CR0
#! < */
#! 227,238c215,218
#! <
#! < #endif /* LinuxBios */
#! < /* begin andrey messing around */
#! <
#! < MOVL $0x80, DX
#! < MOVB $0x11, AL
#! < OUTB
#! <
#! < MOVL tgdtptr-KZERO(SB),GDTR /**/
#! <
#! <
#! < MOVW $SELECTOR(1, SELGDT, 0),AX /**/
#! ---
#! > /* MOVW $SELECTOR(1, SELGDT, 0),AX /**/
#! > BYTE $0xc7
#! > BYTE $0xc0
#! > WORD $SELECTOR(1, SELGDT, 0)
#! 239a220
#! > MOVW AX,SS
#! 243d223
#! < MOVW AX,SS
#! 245,249d224
#! < MOVL $0x80, DX
#! < MOVB $0x12, AL
#! < OUTB
#! <
#! < #ifndef LinuxBios
#! 255,256c230,231
#! < #endif /* linuxbios */
#! < TEXT mode32bit(SB),$0
#! ---
#! >
#! > TEXT mode32bit(SB),$0
#! 266,270d240
#! <
#! < MOVL $0x80, DX
#! < MOVB $0x13, AL
#! < OUTB
#! <
#! 274,277d243
#! < MOVL $0x80, DX
#! < MOVB $0x14, AL
#! < OUTB
#! <
#! 290,292d255
#! <
#! <
#! <
#! 308d270
#! <
#! 320d281
#! <
#! 345,348d305
#! < MOVL $0x80, DX
#! < MOVB $0x17, AL
#! < OUTB
#! <
#! 361,363d317
#! < MOVL $0x80, DX
#! < MOVB $0x18, AL
#! < OUTB
#! 371,374d324
#! <
#! < MOVL $0x80, DX
#! < MOVB $0x19, AL
#! < OUTB
#! p9%
#
#/sys/src/boot/pc/ether.c -- modified to probe for ethernet cards
#rather than expect it to be configured from plan9.ini (there is no
#plan9.ini). all ether devices found are given irq 9 (the geode
#hardwires the INTP lines to 10, but for some reason 10 does not work)
#
#! p9% diff boot/pc/ether.c /sys/src/boot/pc/ether.c
#! 41d40
#! <
#! 62,63c61,62
#! < // if(isaconfig("ether", ctlrno, ctlr) == 0)
#! < // continue;
#! ---
#! > if(isaconfig("ether", ctlrno, ctlr) == 0)
#! > continue;
#! 66,67d64
#! < memset(ctlr, 0, sizeof(Ether));
#! < strcpy(ctlr->type, ethercards[n].type);
#! 73,74c70
#! < i = (*ethercards[n].reset)(ctlr);
#! < if(i < 0) {
#! ---
#! > if((*ethercards[n].reset)(ctlr)){
#! 76,78d71
#! < continue;
#! < } else if(i) {
#! < splx(x);
#! 86d78
#! < //ctlr->irq = 9;
#! p9%
#
#/sys/src/boot/pc/load.c -- hardcoded to boot off 'ether0' as soon as
#it has finished finding and configuring the (missing) pci devices
#and hard drives. if the bootp off ether0 fails (e.g. a bad kernel is
#given) load.c prompts for another boot device. the 'i'm too big'
#check is commented out. console support is hardwired (no plan9.ini
#to turn it on). lots of debuging output to the post card. the
#console() initialization is moved way ahead of everything else -- I
#wanted to have as much debugging output as possible!
#
#! p9% diff boot/pc/load.c /sys/src/boot/pc/load.c
#! 125d124
#! <
#! 149,162d147
#! < static int
#! < myboot(char* file)
#! < {
#! < char *eth = "ether0";
#! < Type *tp;
#! < Medium *mp;
#! <
#! < for(tp = types; tp->type != Tnil; tp++)
#! < for(mp = tp->media; mp; mp = mp->next)
#! < if(strcmp(mp->name, eth) == 0)
#! < boot(mp, file);
#! <
#! < }
#! <
#! 252,254d236
#! < delay(100000);
#! <
#! < outb(0x80, 0x20);
#! 256d237
#! < outb(0x80, 0x21);
#! 258,264d238
#! < outb(0x80, 0x22);
#! <
#! < outb(0x80, 0x27);
#! < consinit("0", "115200");
#! < outb(0x80, 0x28);
#! < kbdinit();
#! <
#! 266d239
#! < outb(0x80, 0x23);
#! 268d240
#! < outb(0x80, 0x24);
#! 270d241
#! < outb(0x80, 0x25);
#! 272d242
#! < outb(0x80, 0x26);
#! 274,277c244
#! < outb(0x80, 0x27);
#! < // consinit("0", "115200");
#! < outb(0x80, 0x28);
#! < // kbdinit();
#! ---
#! > kbdinit();
#! 279,283c246,247
#! < print("hi!\n");
#! < pcihinv(nil);
#! < outb(0x80, 0x29);
#! < // if((ulong)&end > (KZERO|(640*1024)))
#! < // panic("i'm too big\n");
#! ---
#! > if((ulong)&end > (KZERO|(640*1024)))
#! > panic("i'm too big\n");
#! 285d248
#! < outb(0x80, 0x30);
#! 287d249
#! < outb(0x80, 0x31);
#! 297d258
#! < outb(0x80, 0x32);
#! 299d259
#! < outb(0x80, 0x33);
#! 301,304c261,262
#! < // if((p = getconf("console")) != nil)
#! < // consinit(p, getconf("baud"));
#! <
#! < outb(0x80, 0x34);
#! ---
#! > if((p = getconf("console")) != nil)
#! > consinit(p, getconf("baud"));
#! 306d263
#! < outb(0x80, 0x35);
#! 308d264
#! < outb(0x80, 0x36);
#! 318d273
#! < outb(0x80, 0x37);
#! 322d276
#! < outb(0x80, 0x38);
#! 337d290
#! < outb(0x80, 0x39);
#! 365,368d317
#! < outb(0x80, 0x40);
#! < myboot(file); /* hardcoded ether0 boot */
#! < outb(0x80, 0x41);
#! <
#! 443a393,395
#! > extern void diff(char*);
#! >
#! > ulong palloc;
#! 447,448d398
#! <
#! < static ulong palloc;
#! 464d413
#! <
#! p9%
#
#Everything else you'll find in the directory pertains to my attempts
#to fix the missing interrupts problem with the 8259 emulator
#(trap.c). To start clean you may want to remove those files...
#
#------------------------------------------------------
#Changes in the plan9 kernel:
#
#The configuration files are greatly simplified -- I wanted to have
#as little unnecessary drivers as possible. I got the kernel down to
#365K, stripped and gzipped...
#
#/sys/src/9/pc/main.c -- lots and lots of debugging information
#
#in main(). i wanted to make sure that if I crash anywhere during
#execution I could simply se what the post card says and know which
#part of main() i was in... Also some pci debugging information was
#added (pcihinv() prints out the pci devices)
#
#! p9% diff linuxbios/pc/main.c /sys/src/9/pc/main.c
#! 76d75
#! < outb(0x80, 0xA0);
#! 78d76
#! < outb(0x80, 0xA0);
#! 80d77
#! < outb(0x80, 0xA1);
#! 82,83d78
#! < outb(0x80, 0xA2);
#! < kbdinit();
#! 85d79
#! < outb(0x80, 0xA3);
#! 88d81
#! < outb(0x80, 0xA4);
#! 91c84
#! < outb(0x80, 0xA6);
#! ---
#! > kbdinit();
#! 93d85
#! < outb(0x80, 0xA7);
#! 95d86
#! < outb(0x80, 0xA8);
#! 97d87
#! < outb(0x80, 0xA9);
#! 99d88
#! < outb(0x80, 0xAa);
#! 101d89
#! < outb(0x80, 0xAb);
#! 103d90
#! < outb(0x80, 0xAc);
#! 105d91
#! < outb(0x80, 0xAd);
#! 107d92
#! < outb(0x80, 0xAe);
#! 109d93
#! < outb(0x80, 0xAf);
#! 111d94
#! < outb(0x80, 0xb0);
#! 113d95
#! < outb(0x80, 0xb1);
#! 116d97
#! < outb(0x80, 0xb2);
#! 118d98
#! < outb(0x80, 0xb3);
#! 120d99
#! < outb(0x80, 0xb4
#!
#
#------------------------------------------------------
#3. SOURCE CODE
#
#(Missing?)
|
