disk = sdC0
fstype = fossil #| fossil+venti
mbr = yes
fossilp = /dev/$disk/fossil
fossilsrv = installer
fscons = /srv/fs^$fossilsrv^cons
dist = /n/distmedia
distdir = dist
distisfrom=local #| net
installurl = http://10.0.0.1
ventiarena = (/dev/$disk/arenas)
ventiindex = (/dev/$disk/isect)
ventireformat = yes
fat = /dev/$disk/9fat
bootfile = $disk!9fat!9pcf
bootargs = 'local!#S'^/$disk/fossil
bootdisk = $bootargs
venti = '#S'^/$disk/arenas
monitor=vesa
vgasize=1280x1024x32
fn hasmbr {
x=`{xd -b $1 | sed -n '32p;32q'}
~ $x(16) 55 && ~ $x(17) aa
}
fn dombr {
if(~ mbr yes && ! hasmbr /dev/$disk/data)
disk/mbr -m /386/mbr /dev/$disk/data
}
fn partdisk {
disk/fdisk -a /dev/$disk/data
disk/fdisk -p /dev/$disk/data >/dev/$disk/ctl >[2]/dev/null
for(i in /dev/sd*/plan9*){
if(test -f $i){
d=`{basename -d $i}
disk/prep -p $i >$d/ctl >[2]/dev/null
}
}
}
fn diskparted {
mbrandplan9=0
disks=`{ls /dev/sd*/plan9 >[2]/dev/null | sed 's!/dev/(sd..)/plan9!\1!'}
for(disk in $disks) {
if(hasmbr /dev/$disk/data)
mbrandplan9=1
if(~ $mbrandplan9 0)
status='disk not partitioned'
}
fn autotype {
if(~ $fstype fossil)
echo -a 9fat -a nvram -a fossil -a swap
if(~ $fstype fossil+venti)
echo -a 9fat -a nvram -a arenas -a isect -a fossil -a swap # -a other
}
fn prepdisk {
disk/prep `{autotype} $disk
disk/prep -p $disk >`{basename -d $disk}^/ctl >[2]/dev/null
}
fn diskprepped {
if(! test -f /dev/$disk/9fat)
prepdisk=ready
if(! ~ $prepdisk ready){
prepdisk=done
switch($fstype){
case fossil
if(! test -f /dev/$disk/fossil* && ! test -f /dev/fs/fossil*)
prepdisk=ready
case fossil+venti
if(! test -f /dev/$disk/fossil* && ! test -f /dev/fs/fossil*)
prepdisk=ready
if(! test -f /dev/$disk/arenas && ! test -f /dev/fs/arenas*)
prepdisk=ready
if(! test -f /dev/$disk/isect && ! test -f /dev/fs/isect*)
prepdisk=ready
}
}
if(! ~ $prepdisk ready)
status='disk not prepped'
}
fn fmtfossil {
fossil/flfmt -y $fossilp
n=`{cat /dev/swap | grep ' user' | sed 's/^[0-9]+\/([0-9]+) .*/\1/'}
if(test $n -gt 32768)
m=3000 # if have at least 128 user MB, use 24MB for fossil
if not if(test $n -gt 16384)
m=1500 # 64 user MB => 12MB for fossil
if not if(test $n -gt 8192)
m=750 # 32 user MB => 6MB for fossil
if not
m=256 # 2MB for fossil (this will be slow)
# if we're using a venti in the back, take hourly snapshots
# that retire after three days, in addition to the daily dumps at 5am
if(~ $fstype fossil+venti){
v=''
snap='fsys main snaptime -s 60 -a 0500 -t 2880'
}
# otherwise, take the daily dumps but nothing else --
# we can't retire snapshots unless dumps are being archived
if not{
v='-V'
snap=''
}
echo \
'fsys main config '^$fossilp^'
fsys main open '^$v^' -c '^$m^'
'^$snap^'
' | fossil/conf -w
}
fn isfossil {
if(! cmp -s <{dd -quiet 1 -if $fossilp -bs 1024 -iseek 127 | dd -quiet 1 -bs 14 -count 1} <{echo 'fossil config'})
status='no config'
if not if(! cmp -s <{dd -quiet 1 -if $arg -bs 1024 -iseek 128 | dd -quiet 1 -bs 4 -count 1 | xd -b | sed 1q} <{echo '0000000 37 76 ae 89'})
status='not write buffer'
}
fn run_fossil {
echo 'srv -p fs'^$1^'cons' > /env/fossi.$1.conf
echo 'srv fossil.'^$1 > /env/fossi.$1.conf
echo 'fsys main config '^$disk >> /env/fossil.$1.conf
echo 'fsys main open -AWVP' >> /env/fossil.$1.conf
echo 'fsys main' >> /env/fossil.$1.conf
fossil/fossil -c '. /env/fossil.'^$1.conf
mount fossil.$1 /n/$1
}
fn initialise_newfs {
if(! test -s /n/newfs/adm/users){
echo fsys main create /active/adm adm sys d775 >>$fscons
echo fsys main create /active/adm/users adm sys 664 >>$fscons
echo uname upas :upas >>$fscons
echo users -w >>$fscons
sleep 2
}
if(! test -s /n/newfs/adm/users){
status = 'could not create /adm/users'
exit oops
}
for(i in dist dist/replica dist/replica/client){
if(! test -d /n/newfs/$i)
echo fsys main create /active/$i sys sys d775 >>$fscons
sleep 2
}
if(! test -d /n/newfs/dist/replica/client){
status = 'could not create /dist/replica/client'
exit oops
}
if(! test -e /n/newfs/dist/replica/client/plan9.db){
echo fsys main create /active/dist/replica/client/plan9.db sys sys 664 >>$fscons
echo fsys main create /active/dist/replica/client/plan9.log sys sys a664 >>$fscons
}
if(test -d /n/newfs/dist/replica/client && test -f /n/newfs/adm/users){
status = ''
exit
}
status = '/n/newfs/dist/replica/client or /n/newfs/adm/users missing'
exit oops
}
fn havedist {
if(!(test -f $dist/$distdir/replica/plan9.db || test -f $dist/plan9.iso || test -f $dist/plan9.iso.bz2)) {
status = 'No distribution found in '^$dist ' or '^$dist/$distdir
exit
}
if(test -f $dist/$distdir/dist/replica/plan9.db) {
bind $dist/$distdir $dist
bind -a $dist/386/bin /bin
bind -a $dist/rc/bin /bin
}
}
fn isventi {
if(cmp -s <{dd -quiet 1 -if $arg -bs 1024 -iseek 248 | dd -quiet 1 -bs 13 -count 1} <{echo 'venti config'})
exit
status = 'no venti config'
exit oops
}
fn fmtventi {
gg=()
for(f in $ventiarena)
if(! isventi $f)
gg=($gg $f)
if(! ~ $#gg 0) {
status = 'not venti partition : ('^$"gg^')'
exit oops
}
n=-1
fmta=()
for(a in $ventiarena){
n=`{hoc -e 1+$n}
if(isventiarenas $a) {
if(~ $ventireformat yes)
fmta=($fmta arenas$n:$a)
}
if not
fmta=($fmta arenas$n:$a)
}
n=-1
fmti=()
for(a in $ventiindex) {
n=`{hoc -e 1+$n}
if(isventiisect $a) {
if(~ $ventireformat yes)
fmti=($fmti isect$n:$a)
}
if not
fmti=($fmti isect$n:$a)
}
echo Formatting Venti arenas and indices (this takes a while).
# do each disk in parallel
echo good >/tmp/fmt
dd=()
for(a in $fmta $fmti){
d=`{echo $a | sed 's!.*:(/.*/).*!\1!'}
if(! ~ $d $dd)
dd=($dd $d)
}
for(d in $dd){
{
for(a in $fmta){
i=`{echo $a | sed 's!(.*):(/.*/)(.*)!\1 \2 \2\3!'}
if(~ $i(2) $d){
echo $i(3) ...
venti/fmtarenas $i(1) $i(3) || echo bad >/tmp/fmt
echo done with $i(3)
}
}
for(a in $fmti){
i=`{echo $a | sed 's!(.*):(/.*/)(.*)!\1 \2 \2\3!'}
if(~ $i(2) $d){
echo $i(3) ...
venti/fmtisect $i(1) $i(3) || echo bad >/tmp/fmt
echo done with $i(3)
}
}
} &
}
wait
if(~ bad `{cat /tmp/fmt}){
status = 'There were errors formatting the indices and arenas.'
exit oops
}
echo Done formatting Venti arenas and indices.
v=$ventiarena(1)
echo Storing Venti config on $v...
{
echo index main
for(i in $ventiindex)
echo isect $i
for(a in $ventiarena)
echo arenas $a
} | venti/conf -w $v
echo Initializing index...
venti/fmtindex $v
echo Done with Venti!
}
fn download {
baropt='-w 145,129,445,168'
if(! hget -vo /n/newfs/dist/_plan9.iso.bz2 $installurl/plan9.iso.bz2 |[2] bargraph $baropt 'downloading '^plan9.iso.bz2)
exit
mv /n/newfs/dist/_plan9.iso.bz2 /n/newfs/dist/plan9.iso.bz2
if(~ $fstype fossil){
echo fsys main sync >>$fscons
}
if(test -f /n/newfs/dist/plan9.iso.bz2) {
mount /srv/$fossilsrv $dist
distmediadir=/dist
}
if not {
status = 'download failed'
}
}
fn copydist {
if(! test -d /n/dist/dist/replica) {
status = 'missing dist/replica'
exit
}
inst/watchfd applylog 0 `{ls -l /n/dist/dist/replica/plan9.log | awk '{print $6}'} 'Installing file system' &
replica/pull -c / /rc/bin/inst/replcfg
if(~ $status '' *conflicts || test -f /n/newfs/dist/replica/didplan9witherrors)
>/n/newfs/dist/replica/didplan9
if not
>/n/newfs/dist/replica/didplan9witherrors
if(! test -f /n/newfs/dist/replica/didplan9){
status = 'copydist failed'
}
}
fn add_plan9ini {
{
echo bootfile'='$bootfile
echo bootargs'='$bootargs
echo bootdisk'='$bootdisk
echo venti'='$venti
echo monitor'='$monitor
echo vgasize'='$vgasize
echo mouseport'='$mouseport
} >/tmp/plan9.ini
}
fn init_9fat {
if(! test -f $fat) {
status = 'You have no 9fat partition. Can''t setup booting.'
exit
}
if(! test -f /tmp/plan9.ini) add_plan9ini
need9fatformat=no
if(! isfat $fat)
need9fatformat=yes
if not if(! mount -c /srv/dos /n/9fat $fat >[2]/dev/null)
need9fatformat=yes
if not if(! test -f /n/9fat/plan9.ini)
need9fatformat=yes
if(~ $need9fatformat yes){
echo Initializing Plan 9 FAT partition.
disk/format -r 2 -d -b /386/pbs $fat /n/newfs/386/9load
# silently install pbslba if the partition is way into the disk.
# it''s our only hope. only need this for >8.5GB into the disk.
# but...
# there are so few non-LBA bioses out
# there anymore that we'll do this even if we're only 2GB into
# the disk. it's just not worth the headaches of dealing with
# crappy bioses that don't address the whole 8.5GB properly
9fatoffset=`{grep '^part 9fat ' /dev/$disk/ctl | awk '{print $4}'}
if(! ~ $#9fatoffset 1) {
status = 'could not find plan 9 partition.'
exit bad
}
if(test $9fatoffset -gt 2097152) # 2GB
disk/format -b /386/pbslba $fat
mount -c /srv/dos /n/9fat $fat
}
if(! test -f /n/9fat/4e){
cp /n/newfs/386/9load /n/9fat/9load
cp /n/newfs/386/9pcf /n/9fat/9pcf
if(test -f /n/9fat/plan9.ini && ! test -f /n/9fat/plan9-3e.ini)
mv /n/9fat/plan9.ini /n/9fat/plan9-3e.ini
if(test -f /n/9fat/9pcdisk && ! test -f /n/9fat/9pc3e)
mv /n/9fat/9pcdisk /n/9fat/9pc3e
awk -f /bin/inst/mkini.awk >/n/9fat/plan9.ini
>/n/9fat/4e
}
}
fn bootplan9 {
first=`{ls -p '#S' | sed 1q}
if(! ~ $first $disk) {
echo 'warning: The plan 9 partition is not on the boot disk,'
echo 'so making it the active partition will have no effect.'
}
p9offset=`{grep '^part 9fat ' /dev/$disk/ctl |awk '{print $3}'}
if(! ~ $#p9offset 1) {
echo 'could not find plan 9 partition.'
echo 'cannot happen'
exit bad
}
dombr
echo Setting Plan 9 partition active.
p9part=`{disk/fdisk /dev/$disk/data >[2]/dev/null </dev/null |
grep PLAN9 | sed 1q | sed 's/ *(p.) .*/\1/'}
if(~ $#p9part 0){
echo 'You have no Plan 9 partitions (How could this happen?)' >[1=2]
exit 'no plan 9 partition found'
}
p9part=$p9part(1)
{ echo 'A '^$p9part; echo w } | disk/fdisk /dev/$disk/data >[2]/dev/null >/dev/null
x=$status
if(~ $x '' '|'){
echo
echo 'The Plan 9 partition is now marked as active.'
exit ''
}
exit $x
}
fn finish {
echo -n 'Halting file systems...'
if(ps | grep -s ' venti$')
venti/sync -h tcp!127.0.0.1!17034
if(ps | grep -s ' fossil$'){
echo fsys all halt >>$fscons
slay fossil|rc
}
}
|
